Standard Specification For Building Works 2020 Jkr Pdf [repack] ✦ Best Pick
Strict compliance with OSHA and environmental regulations, including waste management and noise control, is required throughout the site. Document Availability
: Rules for prescribed mixes versus designed mixes.
Covers project signboards, legislative compliance, and environmental controls.
| Aspect | 2005 Edition | 2014 Draft (Unreleased) | 2020 Edition | | :--- | :--- | :--- | :--- | | | Max 40 N/mm² | 50 N/mm² | 60 N/mm² (for high-rise) | | Waterproofing | Felt-based | Torch-applied membrane | Liquid PU & cementitious | | Timber | No sustainability clause | Proposed | Mandatory FSC/PEFC for all hardwoods | | BIM Requirements | None | Optional | Mandatory for projects >RM50M | | PDF Availability | Widely leaked | Rare | Official watermark & version control |
Some of the key changes introduced in the 2020 edition of the Standard Specification for Building Works JKR PDF include: standard specification for building works 2020 jkr pdf
| Section Code | Title | Key Changes in 2020 | | :--- | :--- | :--- | | | General Requirements | New clauses on site records, COVID-19 SOPs, and waste management plans. | | B | Site Clearance & Demolition | Stricter noise and dust control (EIA compliance). | | C | Earthworks | Updated compaction requirements (95% MDD for structural fill). | | D | Concrete Works | Mandatory use of high-yield bars (Grade 500). | | E | Masonry | Introduction of lightweight blocks and autoclaved aerated concrete (AAC). | | F | Underwater Concreting | New methodology for marine structures. | | G | Carpentry & Joinery | Sustainability certification for timber (FSC/PEFC). | | H | Waterproofing | Liquid-applied membranes mandated for wet areas. | | J | Roofing | Metal roof insulation requirements (U-value max 0.4 W/m²K). | | K | Finishes (Floor, Wall, Ceiling) | Enhanced slip resistance (R10+ for public areas). | | L | Painting & Decorating | Low-VOC (Volatile Organic Compound) paints only. | | M | Drainage & Sewerage | Integration with SPAN (National Water Services Commission) specs. | | N | External Works | Permeable paving for stormwater management (MSMA 2nd edition). |
Supervisors use the document as a checklist during site inspections. If a contractor pours concrete without conducting a slump test, or fails to provide the required cube test samples mandated in Section D, the supervisor has the contractual authority to halt the works based on these clauses. 3. For Contractors
Disclaimer: This article is for informational purposes. Always refer to the latest official PDF and amendments published by the Public Works Department Malaysia (JKR).
The published by Jabatan Kerja Raya (JKR) Malaysia is a comprehensive document that establishes uniformity in materials and workmanship for public construction projects. This 2020 edition replaces previous versions (such as 2014 and 2005) to incorporate modern construction technologies , updated international standards, and current government policies. Core Purpose and Scope | Aspect | 2005 Edition | 2014 Draft
| Section | Category | Page Range (approx.) | | :--- | :--- | :--- | | A | Preliminaries and General Conditions | A/1 – A/36 | | B | Excavation and Earthworks | B/1 – B/17 | | C | Foundation and Works Below Lowest Floor Level | C/1 – C/69 | | D | Concreting | D/1 – D/68 | | E | Wall System | E/1 – E/20 | | F | Sewerage | F/1 – F/12 | | G | Roofing | G/1 – G/11 | | H | Timber, Joinery and Ironmongery | H/1 – H/37 | | I | Ceiling | I/1 – I/12 | | J | Structural Steel and Metalworks | J/1 – J/9 | | K | Plastering, Paving, Tiling and Carpet | K/1 – K/20 | | L | Water Reticulation | L/1 – L/10 | | M | Rainwater Collection | M/1 – M/6 | | N | Glazing | N/1 – N/7 | | O | Painting | O/1 – O/10 | | P | Roads and Hardstanding | P/1 – P/11 | | Q | Fencing and Gates | Q/1 – Q/4 | | R | Landscaping and Turfing | R/1 – R/10 | | S | Drainage | S/1 – S/8 | | T | Signage | T/1 – T/4 | | U | Slope Stabilisation | U/1 – U/89 | | V | Ground Improvement | V/1 – V/58 | | W | Hydroseeding | W/1 – W/5 | | X | Internal Cold Water and Sanitary Plumbing System | X/1 – X/35 | | Y | Sanitary Fittings | Y/1 – Y/6 |
Based on the significance and implications of the Standard Specification for Building Works 2020 JKR PDF, we recommend:
Details roof trusses, coverings, insulation, and rainwater downpipe systems.
The document serves as the primary technical reference for contractors, consultants, and stakeholders involved in Malaysian construction. Its main objectives include: | | D | Concrete Works | Mandatory
Enhanced compliance frameworks for sustainable material selection, waste reduction, and energy efficiency.
It is designed to be read alongside the Form of Contract (PWD 203/203A) . Structure and Key Sections
Disclaimer: Always ensure you are using the latest, official version from JKR Malaysia for contractual purposes. Proactive Proposal If you're working on a specific project, I can help: Summarize requirements for . Detail the standards for architectural wall systems . Compare the 2020 spec with the 2014 version . Let me know which section you'd like to explore next! Share public link
The Standard Specification for Building Works 2020 JKR PDF is a vital document for the construction industry in Malaysia. Its comprehensive coverage of various aspects of building works provides a standardized framework for contractors, architects, engineers, and other stakeholders. By adhering to this specification, the construction industry can ensure improved quality, increased efficiency, enhanced safety, and compliance with regulations. As the construction industry continues to evolve, the Standard Specification for Building Works 2020 JKR PDF will remain an essential reference point for all stakeholders involved in construction projects.